Hendrickson Truck Parts Catalog

AIRTEK ® with STEERTEK ™ Axle – International Truck Vehicles Built prior to September 2006 – Prior to New Engine Configuration (PEC)

FRONT SUSPENSIONS

■ AIRTEK • Prior to New Engine Configuration ( ♦ PEC) Component Replacement Guide

CURRENT PART NO. ( ♦ PEC) 64583-000 (LH) 64586-000 (RH)

REPLACEMENT PART NUMBER

DESCRIPTION

COMMENTS

Requires the replacement of both air spring brackets, both top pads, lower link mount(s) with the ♦♦ NEC design and the elimination of both upper shock bracket spacers. Contact Hendrickson Engineering for more information. Will continue to be serviced with the ♦ PEC design in the aftermarket.

♦♦ 66775-000 (LH) ♦♦ 66776-000 (RH)

Air Spring Bracket

Lower Link Mount 59429-002

59429-002

Spacer for Upper Shock Bracket

No longer required when the top pad is replaced with the ♦♦ NEC design.

59946-001

See Comments

Requires the replacement of both leaf springs along with the removal of the caster wedge (if equipped), replace with Service Kit 60961-134, see below for contents. Requires the replacement of both top pads, both air spring brackets, lower link mount(s) with the ♦♦ NEC design and removal of both upper shock bracket spacers. Contact Hendrickson Engineering for more information.

Leaf Spring Assembly

65771-000

66420-000

♦♦ 68318-001 (LH) ♦♦ 68318-002 (RH)

Top Pad

64580-000

♦ PEC : Prior to New Engine Configuration, vehicles built prior to 9/2006 ♦♦ NEC : New Engine Configuration, vehicles built after 9/2006

AIRTEK ♦ PEC Replacement Service Kit Contents PART NO. DESCRIPTION

QTY.

60961-134 66420-000

Leaf Spring Assembly Replacement Kit, Axle Set Leaf Spring Assembly, Pre-assembled with Spring End Plate,Thrust washers, Rear Spring Mount, Rear Spring Mount Spacer, and Fasteners ¾"-10 UNC x 8½" Hex Bolt (Clamp Group)

58917-016 22962-001 17700-033 58917-008 22962-033 49842-000

10

¾" Flat Washer

8 8 2 8 4

¾"-10 UNC-2B Nylocknut

¾"-10 UNC x 6" Hex Bolt (Rear Hanger)

¾" Flat Washer

¾"-10 UNC-2B Nylocknut

NOTES: * Not supplied by Hendrickson, used for reference only. Hendrickson is not responsible for components supplied by the vehicle manufacturer. For assistance with maintenance and rebuild instructions on these components see vehicle manufacturer. ** Item included in kit / assembly only, part not sold separately. *** Axle spring seats come assembled with the axle beam and are not serviceable. **** Effective January 2019, vehicles equipped with Hendrickson STEERTEK NXT/ STEERTEK axle will be installed with a left hand composite bearing and a right hand roller bearing configuration to replace the previous roller / roller bearing configuration for production and aftermarket. ***** The recommendation of the vehicle manufacturer is that dual height control valves are only to be installed on the front suspension when the rear suspension is equipped with a single height control valve system.This arrangement is best suited to keep the vehicle level versus having dual height control systems on both the front and rear suspensions. ****** No longer available for service, see Replacement Guide on Page 140.

HENDRICKSON AIRTEK Ride Height Gauge for International Truck Vehicles Literature number 45745-251 can be obtained online at www.hendrickson-intl.com/Litform

140

www.hendrickson-intl.com | Reference Lit. No. SP-182

Powered by